I cannot repair my washing machine without documentation. I have no idea how to use my multimeter to check the components. There are parts dealers for Beko in my area, but none of them have the service manual.

The parts shops all say go to the website for the manual as a flippant off-the-cuff answer. There are no service manuals on the Beko website -- at least not for my model. The navigation of the Beko website does not even have a path to docs. And worse, my model is treated as non-existent by the website.

What would I do if I were a professional repair service? What is the official channel?

I am open to “piracy¹” but it would be a long shot to scour all the dark web for a manual for a specific washing machine. It’s not the type of content people have a strong interest in spreading/trading.

¹As RMS says, it’s not a just and appropriate term for it (but “sharing” is awkward too).

(update) Added frame from Youtube video t1XaUolbjLY which shows that service manuals exist for at least some Beko models. As we can see in the snapshot, Beko wants to restrict who is servicing their machines. (btw the video covers a very different model than mine).

I probably need to find the test mode for my machine, comparable to YT video cq_uSyghZC0.

new problem

The machine reached a new low. Now there actually is a problem with the water valve, it seems. When running a program, it pauses then the start button just blinks. (It previously started by pumping then at least filled the tub). So I followed this video from the 5m10s position. I do not get 220v on either valve. But certainly I can see that 220V is getting to the control panel. So 220v goes into the control panel, but does not make it out of the control panel leads where the water valve connects.

(edit) The water valves themselves are fine (I connected 220v directly to the water valves and water flows). I guess I should suspect the pump now. The pump was actually the very first task back when the machine worked. So I should not have even been looking at the water valves which only start after the initial pumping ends.

I really enjoy the arcade blogger for the arcade cabinet raid writeups he does, and his step-by-step repair posts. The history aspect is neat too.

This is a repair post with a bit of history.

Decades ago, to combat ROM-cloning piracy, Capcom started adding a chip to their PCBs that stored encryption keys in memory backed up by an onboard battery. You may see the problem here - batteries are not meant to last forever, and if the chip lost power AT ANY TIME the keys were lost and the game was unplayable.

This feels like yet another example of the total disregard corporations hold for the media they own the rights to, in favor of short term profits. We've seen before that many works produced by entire teams would have been lost if not for the efforts of pirates and amateur archivists.

To quote the blog: >Its hard to say if Capcom knew this would happen, but then again, the shelf life of most arcade games was months, or at most a couple of years – I guess it wasn’t something they planned for.

Fortunately, this is a well established problem with a motivated, technically-minded community looking for a solution, so this early DRM has already been circumvented. The article doesn't go into detail on how they researched and reverse engineered this sabotage, but I might do a little reading and edit the post if I find anything cool.

Edit: this seems to have more details and is an interesting read so far: https://arcadehacker.blogspot.com/2014/11/capcom-kabuki-cpu-intro.html?m=1

The gist is that the problem is well solved at this point and there's a small industry of aftermarket components out there that are nearly plug and play. The version the author went with works like this:

You desolder the dead battery and replace it. Then desolder the blank sabotage chip. You swap in the aftermarket one and configure it (by using tiny switches) to inject the correct set of encryption keys. Then you slot the blank sabotage chip into the aftermarket one.

When the game is powered up, the aftermarket chip restores the encryption keys, the PCB looks for the keys, then successfully used them to run the game files.

The cool thing is that the sabotage chip is now functional again on its own.

The author spent some time restoring the board to stock, by keeping the sabotage chip powered with another battery while removing the aftermarket chip so it could be used elsewhere. I should appreciate the effort at not wasting any resources but I think it makes sense to keep the de-sabotauge chip as a permanent addition, as it automatically prevents the kind of data loss the company intended.

Either way, it's a neat article and I'd recommended reading it. He does a lot of arcade cabinet restorations, but generally sends the electronics away for repair, so this was a neat one.

I know tech has come a long way since these were made but there's something to be said for these big, chunky, through-soldered components and the well-documented wiring instructions that often came with them.

Decided to restore this old thing from out in the shed. It was in the weather for a couple of years, and I think it's 20+ years old.

Replaced the pump with a USB powered 5 watt silent one.

Replaced the halogen lamp with an LED one.

Cleaned as much as I could.

Seems to be working well. How long the $12 ebay pump lasts remains to be seen.

More pics at https://photos.app.goo.gl/HDmVb2K1MeUQTfuG8

Hi,

Is there good literature on how to repair stuff? Just general things, not specific appliances. How to repair wood, how to properly sand wood and metal, how to replace a tile, how to read and analyze circuits, identify faulty parts and correct replacements, etc. I just want to become better at repairing stuff.

I do not know if these have been posted yet, but I thought I would share them just in case

• Car Complaints: https://www.carcomplaints.com/
• Motor Online: Vehicle Information Library: https://vil3.motor.com/LogIn.aspx

!

I bought this set of outside calipers at a junk store in my hometown (sort of a consignment, thrift store deal, with lots of old furniture, and the contents of like half a dozen garages right down to the old jars of mismatched screws. I sort of use it like a hardware store).

I like this design a lot, I like the lack of a spring on the jaws, and that you can fasten the little distance measuring arm to the side it measures on, so you can close the calipers around something, tighten that wing screw, then open the calipers to get them back.

!

They had some surface rust, so I decided to clean them up. The first step was to disassemble them. Not difficult when there's only three pieces involved.

!

I let them soak in some evaporust for about 8 hours. I really like this stuff, it hits the sweet spot between very effective and not especially dangerous, and it's reusable! They do overestimate how effective it is in their instructions though, so it often takes longer.

! The calipers, straight out of the evaporust. You can already see some text which was hidden before, along with the initials AM from a previous owner.

Now that the worst of the rust had been dissolved, it was time to switch from chemical to mechanical cleaning. I sanded it down with 400 grit emery cloth.

! The calipers with only one side sanded.

As I cleaned up the sides, I found a few neat bits of history:

! Here's some funny nicks up near the joint on one side. I wonder what caused them. And the previous owner's mark on the right side, AM. This is a big part of why I love old tools. I love the history they carry with them, even if I don't know all of it.

! Looking better, but still a ways to go. I was surprised to find that there weren't any markings on the little distance arm. I'd been expecting to find little angle tickmarks or something, maybe even printed numbers, but there weren't any to be seen after the evaporust, or once I started gently sanding off the remaining rust and the black crud evaporust leaves behind.

Once I had most of the rust gone, I switched to steel wool. I didn't want to take too much material off the surfaces, and I felt the more flexible steel wool would hit inside the pitting from the rust better.

!

The steel wool shined it up quite nicely. And here's a closeup of some of the surface pitting left over by the rust on the left side. The back of these calipers didn't have this kind of damage.

It was tempting to leave it here, but I didn't want the rust to return, so I decided to treat the calipers with cold blue, to provide some protection against oxidation. There are other ways to protect steel, but I like the look and it seems to hold up well enough.

!

Cold blue always looks a little rough when it first goes on (this stuff is a gel you don't want to get on your hands. You wipe it on, leave it to darken the metal for 60 seconds, and wipe it off again) but a little burnishing with 0000 steel wool will tidy it up:

!

There we go, still pretty shiny, but not as likely to rust again. Not bad considering how it looked in the beginning. Hope you'd approve, AM.

(I wrote this post for the making/fixing things blog I have on our local movim instance. If you're a slrpnk.net local, your credentials will work on movim automatically!)

cross-posted from: https://feddit.cl/post/2652008

> Kobo and iFixit partner for OEM parts and repair guides

Refrigerator is a Frigidaire LTFR1832TF0.

Leak came from the front-right side.

I did not notice any temperature fluctuations, but I also don't notice much of anything. It still seemed cold when I unplugged it, though!

Checked the drain pan & it seems dry? Not overflowing or anything.

No water on inside of refrigerator.

Anyone have any idea what might be going on? I'd really appreciate it, as no one can take a look for another 3 days.

I don't want my food to spoil, as I don't have a lot of money. I just want to know if it'd be safe to plug it back in!

Thank you.

EDIT: had my BIL stop by to take a look. More than likely it's refrigerant. The compressor was fine, but one of the lines on it would not get cold, so that's that. Probably a leak in the line, more than likely from a failed seal.

The cost to refill the refrigerant / repair the line / seal would cost waaaaay more than a new fridge, unfortunately.

Thanks, y'all. Appreciate the help and advice.

!

This was a pretty quick little project - some of my friends recently bought a house, it came with a shed, and the door of that shed was broken. The design of the door allowed it to swing open about 180 degrees, at which point it'd hit its own frame.The wind must have caught it one day and swung it open hard. When that big wide door hit the frame so close to its fulcrum, it just snapped right down the line. It also bent all the hinges.

!

The previous owners tried to fix it, it looks like by lifting the door back in place and driving some mismatched screws through some wood scraps and metal plates. That left the door drooping, hanging crooked in the frame, and flexing kind of alarmingly when it opened.

We'd talked about taking it down and fixing it properly, I even took some measurements.

Then one morning I got lucky, I saw a post on our local Buy Nothing -type page where someone was offering up some 1"x12" boards they'd been using as shelves in a shed. They were a bit weathered but otherwise in good shape (no cracks, warp, or rot). It was trash day in that neighborhood so I hustled out there and claimed the whole pile. 1"x12"s ain't cheap.

!

On the way back I picked up a shovel with a cracked handle which I fixed with a hose clamp and have been using for a couple years now.

We set a day, I packed the lumber and tools, and we started in on the shed. I think we also planted a peach tree (using my new shovel) that day.

We started by taking the door off the shed and setting it on some sawhorses I brought.

! (Dog helping hold down the door)

This was where we made our first unfortunate discovery. The shed was older than we'd realized. The 1"x12"s the door had been made from were rough cut, not dimensional, so the boards I'd brought were about half an inch narrower, and a quarter inch thinner than the originals.

So we had a couple options here - all the boards were rotten for a few inches of the bottom. We could replace all of them with the new ones, which would be a close fit of all our materials, and would lose us a couple inches of width unless we added another board, or we could save lumber all around and change the design to keep most of the existing door but make it a little janky. They were good with that, so we did a kind of strange design.

First we removed the split board and it's support scraps and set them aside. Then we cut one of the new boards to the original/final height of the door.

Next we measured far enough up to catch all the rot, and we cut the door that much shorter.

!

We attached the new vertical board so it extended a couple inches at the top and bottom (it's on the right in the picture above). Then we added two braces across the face of the door, so they went across at the final height of the door/the long new board, leaving a bit of space above and below the old boards. These would add some extra ridigidity, by having pieces going across on the front and the back, and they'd hide the difference in length. Then we cut some pieces to go behind them, fitting flush above and below the old boards. These weren't structural, they just took up space so critters and weather wouldn't get in.

!

Once the door was made, we started looking at hanging it again.

Unfortunate discovery two: the doorway was crooked. Part of that was the fault of the badly rotted board which crossed the doorway under the door. It didn't seem to be doing anything but catching rain and soaking it up, so we pried it off and replaced it. Luckily it only crossed the doorway, it wasn't actually part of the building frame, which seemed to be in okay shape. The top of the doorway was also out of square, but not enough to be a major problem. As they reminded me a few times, it's a shed, not a house.

We straightened out the hinges by putting them on a brick and pounding on the high points with a small sledge (not ideal but it worked). Then we hung them back up and attached the door. From what I remember, it sat just above the new lower plate when it was closed, might have rested on it but I don't remember.

!

The last step was to cut a thin piece to attach to the inside of the door frame to make up for the width lost by replacing a roughcut board with dimensional.

!

From there, I think we called it good. It had rained on and off during the project, and we didn't want to re-attach the trim while it was wet for fear of trapping water between the boards.

We cleaned up the tools and had some pizza.

As a side project, I took the original, very rotted wooden door handle, and the scraps of the split board. From the dimensions of the original and the look of the wood, I figured they cut the original from scraps of the same roughcut 1x12s they built the rest of the shed out of, so I wanted to make the replacement the same way.

!

I traced the original onto the wood, flipped it end for end, and traced it again, and sort of averaged the two. The original wasn't actually symmetrical but my replacement would be much closer. Then I started sanding it down until it was comfortable to hold. I pre-drilled the holes for the screws, including space for the heads, so they wouldn't split the handle when it was attached.

!

I stained it, I think my usual mix of Gunstock and Red Oak, then applied a few coats of urethane, sanding lightly between coats. I even got the back, where it'd touch the door, and the holes for the screws. I figured they could paint it whatever color they painted the door, like the original, or leave it as-is, either way it'd be very waterproof and last a long long time.

!

All it needs now is a new coat of paint.

I am quite happy so far with my FP5. But I am looking forward to the upcoming Ubuntu Touch and Mobian ports.

Once you get access to a laser cutter, you start to see all kinds of places you can use it in a project. Our local makerspace has one, and the more I use it, the more I find new applications, whether that’s in fabrication of flat parts, or just adding flair to smaller panels of a large project.

Around Christmas, I decided I was going to fix up my dad’s miter saw. It was an older, discontinued Delta 36250. The guard was missing(my grandfather didn’t believe in tools having guards) and the plastic insert in the table, where the saw blade came down, had been shattered for years.

The guard was an easy fix, bought a replacement part from ereplacementparts. But the plastic inserts were out of stock. In fact, even the scam parts websites that all look identical weren’t bold enough to lie and claim to have any of these things. Having examined what was left of the original, here’s my theory for why:

They’re junk. The space they fill is 5mm deep, but they were made to be cast out of plastic about 2mm thick with a lip around the edge to fill in the space. That plastic was super brittle. And then,just to make things better, the slot in the plastic, where the saw blade would go when it cut through the wood, wasn’t wide enough to accommodate the blade when it was rotated to do cuts at a 45 degree angle. Which it was designed to do. So the blade would come down through the wood, hit the brittle plastic at the wrong speed and blade type for cutting plastic, and shatter it. The inventories were out of stock because everyone broke theirs and ordered new ones, and they weren’t worth making in the first place

The obvious answer was to cut something close enough out of plywood and call it a day, but I wanted to get fancy with it. So I took some pictures, removed all the screws, claimed all the shards of plastic, measured the space, and brought the pieces home. Luckily enough pieces of the insert remained to get every measurement except overall length (which I measured while I was there). I used my calipers to get the original slot width, positions of the screw holes, etc. I drew up a vector image with my best guess at the final dimensions, and widened the slot until it slightly exceeded the damage marks from when the saw cut into it at a 45.

To get the curve at the corners I scanned in one of the shards, pasted it into the schematic in inkscape, and adjusted the rounded corners setting on the rectangle until it matched the scan.

On our makerspace night I cut a few cardstock templates, chased the screw holes around the design until they lined up with my plastic shards. And because I like adding some decorative aspect to practical items, I also drew up and cut a stencil of the name of his old military unit surrounded by a hawser rope.

This is one of the places the laser cutter really shines. When I was doing spray paint stencils in the past, I always cut them by hand with a scalpel blade(ironically cheaper than xacto knife blades). But this is tedious, takes forever, and certain designs really don’t lend themselves to it, so you find yourself spending lots of time gluing your bridges back together as they tear or bend. With the laser cutter, I had a template literally in minutes, and at least as precise as I could have done it. Some folks feel the art looses something when you make it easy that way, I’m personally more about results, especially when I’m on a timeline.

The makerspace didn’t have any plexi in the thickness I needed for the insert, so I reached out to TAP plastics for a recommendation. They had 4.5mm High Impact Modified plexiglass which they’d ship in custom dimensions, so I could get something small enough to fit inside the cutter. I went ahead and ordered that, and about a week later I had it. Enough material for four tries.

We ran the first cut slow in order to cut the thicker-than-usual plexi. That ended up melting it a bit along the edges and at the holes, so we did the second in two passes. I also redesigned the vector with smaller holes, and sent it again. This one came out better dimensionally, but the cutting fogged the plexiglass (it was the kind protected by sheets of plastic rather than paper, so we had to remove the stuff before running it in the laser). This wouldn’t be a problem except that I was planning to stencil the art onto the back of the plexiglass, so it would look deep and glossy, and would be protected by the plastic itself.

I covered the remaining material in painter’s tape and ran it again. The third one came out great, and I took them home for finishing.

The next step was to chamfer the screw holes on the drill press.This would let the heads of the screws sink down into the plastic where they’d be out of the way of boards sliding across the worktable.

Once I had that done, I peeled the painter’s tape off the back,and for once managed to remember to double check that it was actually the back and oriented correctly and everything. Then I attached the stencil so it was mirrored. I normally use temporary spray adhesive where I can to fasten the stencil down, to minimize the underspray. But a reverse stencil means any glue residue would end up between the plastic and the next coat of paint, so I had to skip it and just use stencil spiders (little metal weights, usually nuts, with paperclip/wire legs, which help you pin down high points).

I got very lucky, the paint went on well and didn’t leave me with any spots I had a problem with. I gave it a couple days to dry before messing with the stencil (this was good graff artist paint, but I’ve had the cheap stuff dry tacky, then when you try to lift the stencil, the paint stretches, snaps, falls onto the work and bonds there. I didn’t think that would happen with this stuff but I wanted to be really sure). Waiting to find out if it came out okay is the worst part, for me.

When that was dry I checked it over, and painted on the background color.

By that point, I was out of time to check it for fit, so I wrapped it and waited until Christmas to find out if it would fit. Later that day, we tested it, and it was overall pretty good - I had to chamfer the holes a bit deeper on his drill press, and used a thin round file to adjust a couple of them just a touch outwards from the center. But it fit and looked quite nice overall. My vector file isn’t perfect, but I’m providing it on my website just in case anyone out there has a compatible saw and also access to a laser cutter, and for some reason wants to follow me down his road.

The saw file is available here as a pdf: https://jacobcoffinwrites.files.wordpress.com/2024/01/saw-insert-great.pdf (apparently wordpress won't host SVG files.)

And here as both pdf and svg: https://mega.nz/folder/CdMwVDQa#yiHp5k_WbOxrNcYCRwWyiA

(Sorry not to show the stencil, I realized partway through writing this that my dad wouldn't appreciate it if I did, but I still like talking about the stencil art process.)